gototopgototop

www.kukata86.com

 Bulgarian English

Last forum activity on Mirror "Tube":

No posts were found
             

Last comments:

  • hello sir good evening sir actully i have purchased your application and i have programmed the ardui... more...
    25.01.17 20:32
  • Dear Sir, I am in need to copy a RFID 125kHz encrypted card, so is your device able to copy encrypte... more...
    29.03.16 06:26
  • Hi... very very good job!! please... i have a question ... if you have time to answer or if you can.... more...
    15.02.16 20:33
Files for download (PDF)

( 2 Votes )

 

 

 

Led Board 8.7сmХ 1.5cm - 4 LEDs

Board Top

Download in PDF

Board Top with white mask

 

Download in PDF

Board Bottom (mirrored)

Download in PDF

 

 

Led Board 19.5cm Х 1.5cm -  9 LEDs

Board Top

Downlado in PDF

Board Top with white mask

Downlad in PDF

Board Bottom (mirrored)

Download in PDF

 

Led Board 39cm X 1.5cm - 19 LEDs

This board is divided into two parts. To be printed in real size is divided into two A4 sheets.

Board Top

Part 1

Download in PDF

Part 2

Download in PDF

Board Top with white mask

Part 1

Download in PDF

Part 2

Download in PDF

Board Bottom (mirrored)

Part 1

Download in PDF

Part 2

Download in PDF

The accompanying drawings boards are life-sized. For the preparation of PCB important to use methods of amateur laser printer or photo-method

In the attached file the top of the board is flipping to be suitable for carrying laminated after printing.

 

List of elements for LED boards

Component

Description

R1,R2,R3

820 Ohm / 0.25W

LED

5mm RGB-Led (OPEN Cathode)

 

Schematic of Controller for mirror "Tube"

Download in PDF

 

IMPORTANT!

The board is designed for external LED driver and power bridge.Limit from  500  leds written on the board  do not apply to the configuration in this article. Described below circuit can drive up to 300 LEDs from RGB LED boards, which is about 7A in light of all colors. (in LED borards each LED consumes 3x15mA = 45mA but as managed by PWM and constant glow about 22 mA forLED is about 300 LEDs) With LED strips you must comply with their individual consumption. To control more LEDs use other switching transistors and bridge rectifier or put the second mirror controller

 

Board of Controller

Controller board - Top

Download in PDF

Controller board - Top with white mask

Download in PDF

 

IMPORTANT!

The board is designed for external LED driver and power bridge.Limit from  500  leds written on the board  do not apply to the configuration in this article. Described below circuit can drive up to 300 LEDs from RGB LED boards, which is about 7A in light of all colors. (in LED borards each LED consumes 3x15mA = 45mA but as managed by PWM and constant glow about 22 mA forLED is about 300 LEDs) With LED strips you must comply with their individual consumption. To control more LEDs use other switching transistors and bridge rectifier or put the second mirror controller

Controller board - Bottom

Download in PDF

 

List of Elements for the Controller

Component

Description

D1

RS 804 Bridge (8A/400V)

C1

2200uF / 25V

C2

1000uF / 16V

C3,C4

100nF / 50V

R1,R3,R5

100k / 0.25W

R2,R4,R6

10R / 0.25W

R7

1k / 0.25W

R8

47K / 0.25W

U1*

PIC 12F629

U2

LM7805

Q1,Q2,Q3

IRL540

RGB-OUT, IN1, SWITCH

6 PIN connector

Download in PDF

 

Files for Download

Source code – This is the source code of the program with which you can create your own management regimes LED boards

MPLAB IDE – it's Microchip program to build a HEX file of your choice modified source code.

HEX file – It was created by software that fills me optimal chip and offers quite a variety of operating modes of the controller

The password for all archives in the article is: www.kukata86.com

 

7-seg. coundown count.

Gallery (OTHER)

Info Bulletin:

Paypal Donation:

Donation development projects.

Amount: